No products in the cart.
Universal
Showing 1–20 of 44 results
- Accessories adapters cables, Universal
Abrites cable for CAN connection CB021
Connection cable CB021 is used for the internal CAN connection when performing key procedures on Renault and Nissan vehicles. It can also be used for mileage recalibration and module replacement on selected Renault models.
SKU: MS.CB021.AB - Accessories adapters cables, Universal
Abrites cable for CAN-BUS CB012
The JLR All Keys Lost wiring kit is essential in some cases during the key programming procedure when a direct connection to the CAN-BUS is required. The software automatically detects the platform on which the vehicle is based and prompts the customer when such a connection is required. The cable is connected between the AVDI and the OBDII cable.
SKU: MS.CB012.AB - Accessories adapters cables, Universal
Abrites kit for programming BMW Moto keys SET307
The SET307 kit includes a special cable and antenna designed for programming keys in BMW motorcycles equipped with a smart key. It allows programming of keys both directly in the vehicle (when the key is on the assembly table) and on a workshop bench — useful in situations where all keys are lost or when making a spare key.
SKU: MS.AB.SET307 - Accessories adapters cables, Universal
Adapter FIAT SGW Bypass Security Gateway FCA SGW
FIAT SGW Bypass Security Gateway FCA Adapter
The universal FCA 12+8 adapter allows bypassing the Security Gateway (SGM/SGW) in FCA Group vehicles from 2018 onward, restoring full access to diagnostic functions such as clearing error codes, performing actuations, and ECU programming.
SKU: MS.AD.FCA - Accessories adapters cables, BDM Frames / Adapters / Needles / Openers, Universal
Adapter FTDI2232 UART ver.3.0
Accessories adapters cables, BDM Frames / Adapters / Needles / Openers, UniversalAdapter FTDI2232 UART ver.3.0
Universal adapter for interfacing with microcontrollers via UART, MBUS.
The board has the following outputs: DTR, DTS, DT2,TX, RX, VCC (the adapter allows you to supply this output with any voltage up to 36 V applied to the DC 2 mm input), GND, 3.3 V (voltage from the USB port via a stabilizer), 5 V (voltage from the USB port), MBUS (enabled by a jumper on the board). Jumper for switching MBUS mode. Reset button is used to reset the FTDI2232H microcontroller to its original state.
Currently supported by:
1. license 22 Cypress/Fujitsu/Spansion MB91F0xx/S6J3xx MCU UART
2. license 48 Cypress/Fujitsu/Spansion 96Fxx MCU UART
3. license 55 Renesas RH850 R7F701xxx MCU UART
4. license 59 – Renesas V850 MCUSKU: MS.FTDI2232 - Accessories adapters cables, Electronic equipment, SRS, Universal
AirBag tool and accessories storage case AST CPT Diagcar Airbag Service Tool
Accessories adapters cables, Electronic equipment, SRS, UniversalAirBag tool and accessories storage case AST CPT Diagcar Airbag Service Tool
AirBag tool and accessories storage case AST CPT Diagcar Airbag Service Tool
AirBag Service Tool Case designed to contain tools and accessories.
All protected and in one place.
High quality made, protect Your electronic device and all accessories.
Case can be a great extension of your existing set, especially for people working outside the workshop.NOTE:
Empty Case. No device and cables inside.SKU: MS.AB.CAS - Accessories adapters cables, Universal
Bosch EDC7 Universal Adapters
Bosch EDC7 universal terminal adapter cables with 0.1uf capacitors in-line, Universal fitment for bench connection where an in-line capacitor is needed. Simply plug into the end of the existing breakout cable and get the job done.
Approximately 100mm in length.Set of 2 piecesSKU: MS.EDC7.Bosch - Accessories adapters cables, Universal
Cable Bench Isuzu Transtron M3SC
The Bench Isuzu Transtron M3SC diagnostic cable is designed for reading and writing the memory of the ECU engine controller in vehicles with the Transtron M3SC system. It allows you to work with the ECU without having to remove it, which is particularly useful in workshops dealing with electronic diagnostics.
SKU: MS.COBD.Transtron.M3 - Accessories adapters cables, Universal
Cable Bench Isuzu Transtron M5/M5S
The Bench cable for Isuzu Transtron M5/M5S (ECU) controllers enables convenient and safe programming and diagnostics.
Thanks to the built-in ignition switch and 120Ω CAN resistor, the cable allows for full simulation of operating conditions in the car.SKU: MS.COBD.Transtron.M5 - Accessories adapters cables, Universal
Cable Denso 275700-5XXX Kubota Kia Hyundai DSM Bench
Bench cable designed for Denso 275700-5XXX series ECUs used on Kubota, Kia, Hyundai, Hino and DSM engines, among others. It allows the ECU to be connected to a programming tool outside the vehicle, preventing damage to ECU pins and facilitating diagnostics or software modification.
The cable works with popular programming tools such as:
New Trasdata
It also supports drivers from SH72546 for Hyundai/Kia ECUs (e.g. MB275700-5715).
SKU: MS.275700-5XXX - Accessories adapters cables, Dimsport, OHW / AGV, Universal
Cable Kess EDC17CV41 Bench
EDC17CV41 cable for use with the flasher. Used for easy connection to the ECU without the risk of pin bending, and saves a lot of time.
EDC17CV41 Iveco
EDC17CV41 Doosan
EDC17CV41 Hino
EDC17CV41 Isuzu
EDC17CV41 New Holland
EDC17CV41 Case
EDC17CV41 SteyrvThe cable provides a single cable solution in which type 1 and type 2 are selected via a switch.
Both type 1 and type 2 are supported.
Total length: Approx. 1.5 mSKU: COBD.EDC17CV41.KESS - Accessories adapters cables, Universal
Cable Kess MD1CE100/01 Bench
Kess cable MD1CE100/01
MD1CE100
MD1CE101
MD1CE108
for use with the flasher. Used for easy connection to the ECU without the risk of bending pins, and saves a lot of time, and time is money.MAN, Iveco, Case, Claas, New Holland, Dongfeng and Steyr engines
SKU: COBD.MD1CE100/01.Kess
