No products in the cart.
Accessories adapters cables
Showing 1–20 of 361 results
- Accessories adapters cables, Alientech, Cables, Dimsport, Truck / CV, Truck / CV
14-pin cable for Deutz F32GN064, 144300K232
Accessories adapters cables, Alientech, Cables, Dimsport, Truck / CV, Truck / CV14-pin cable for Deutz F32GN064, 144300K232
1 in stock
Truck diagnostic cable with connection to the 16-pin Scania truck diagnostic system.
COBD replacement for Alientech 144300K215 and Dimsport F32GN020.
Length: (Approx) 2.5m
SKU: F32GN064 - Accessories adapters cables, Universal
Abrites cable for CAN connection CB021
Out of stock
Connection cable CB021 is used for the internal CAN connection when performing key procedures on Renault and Nissan vehicles. It can also be used for mileage recalibration and module replacement on selected Renault models.
SKU: MS.CB021.AB - Accessories adapters cables, Universal
Abrites cable for CAN-BUS CB012
Out of stock
The JLR All Keys Lost wiring kit is essential in some cases during the key programming procedure when a direct connection to the CAN-BUS is required. The software automatically detects the platform on which the vehicle is based and prompts the customer when such a connection is required. The cable is connected between the AVDI and the OBDII cable.
SKU: MS.CB012.AB - Vvdi prog, Xhorse
Adapter BCM 2-Keytool PLUS / MINI PROG / VVDI PROG
In stock
Adapter BCM 2-Keytool PLUS / MINI PROG / VVDI PROG
BCM 2 adapter that allows you to read data from protected BCM 2 modules found in Audi.
Included are:
- xdnp63 needle adapter
- xdnp64 needle adapter
- 4 x locking plates
- Cable for Keytool PLUS / MINI PROG
- Cable for VVDI PROG
- Cable for soldering
- 6 x mounting screws
Adapters enclosed in a protective plastic box.
Application:
- Audi 2013-2019 A4, A5, Q5 (list of supported SW versions can be found directly in VVDI PROG/MINI/PLUS)
- Audi 2013-2019 A6, A7, A8 (list of supported SW versions can be found directly in VVDI PROG/MINI/PLUS)
SKU: MS.BCM.2KEY - Accessories adapters cables, Adapters, Dimsport, New Trasdata
Adapter Bench DIMSPORT New Trasdata to read RENESAS (M32, M32R, M32Rx) F34NTA13
Accessories adapters cables, Adapters, Dimsport, New TrasdataAdapter Bench DIMSPORT New Trasdata to read RENESAS (M32, M32R, M32Rx) F34NTA13
1 in stock
The adapter is used to read RENESAS (M32, M32R, M32Rx) F34NTA13 engine controllers. It allows the NEW TRASDATA device to be connected to the ECU.
SKU: F34NTA13 - Accessories adapters cables, Adapters, Alientech
Adapter for Mercedes TEMIC cable with OBD2 socket
1 in stock
TEMIC bench controller connection adapter is a replacement for Alientech: 144300K251, Dimsport: F32GN053 cable
To connect requires OBD2 cable for Kess: 144300K249 or New Genius: F32GN051SKU: MS.MB.TEMIC - Accessories adapters cables, BDM Frames / Adapters / Needles / Openers, Universal
Adapter FTDI2232 UART ver.3.0
Accessories adapters cables, BDM Frames / Adapters / Needles / Openers, UniversalAdapter FTDI2232 UART ver.3.0
2 in stock
Universal adapter for interfacing with microcontrollers via UART, MBUS.
The board has the following outputs: DTR, DTS, DT2,TX, RX, VCC (the adapter allows you to supply this output with any voltage up to 36 V applied to the DC 2 mm input), GND, 3.3 V (voltage from the USB port via a stabilizer), 5 V (voltage from the USB port), MBUS (enabled by a jumper on the board). Jumper for switching MBUS mode. Reset button is used to reset the FTDI2232H microcontroller to its original state.
Currently supported by:
1. license 22 Cypress/Fujitsu/Spansion MB91F0xx/S6J3xx MCU UART
2. license 48 Cypress/Fujitsu/Spansion 96Fxx MCU UART
3. license 55 Renesas RH850 R7F701xxx MCU UART
4. license 59 – Renesas V850 MCUSKU: MS.FTDI2232 - Accessories adapters cables, Key tool, OBD Star, Xhorse
Adapter OBD II FCA 12+8 SGW Security Gateway
Out of stock
All FCA vehicles after 2018 are equipped with a SGW security gateway module to prevent attacks on the vehicle’s network via the CAN bus.
Direct connection to the OBD II-16 connector does not always give the required results-you can read errors but not clear them, you cannot program the controllers as well as make adaptations/adjustments, etc.
In the case of this problem, you can bypass the SGW (Security Gateway) using the presented adapter so that full communication functionality is available.
SKU: MS.AD.FCA.SGW - Accessories adapters cables, OBD Star
Adapter OBDSTAR P003 ECU BENCH/BOOT
Out of stock
OBDSTAR adapter designated P003 designed to work with drivers using devices such as:
- X300 DP PAD
- X300 DP PLUS
- X300 series
- KM DP PLUS
With this adapter you can read the engine controllers in BENCH and BOOT mode in order to obtain the PIN, CS, or other data needed for IMMO.
SKU: MS.AD.P003 - Accessories adapters cables, Cables bench, MagicMotorSport – Flex
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42A
Accessories adapters cables, Cables bench, MagicMotorSport – FlexAdapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42A
Out of stock
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42A
Connectors size A, which are included in the basic FLEX device.
The FLK42A adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
SKU: FLK42A - Accessories adapters cables, Cables bench, MagicMotorSport – Flex
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42B
Accessories adapters cables, Cables bench, MagicMotorSport – FlexAdapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42B
Out of stock
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42B
Connectors size B, which are included in the basic FLEX device.
The FLK42B adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
SKU: FLK42B - Accessories adapters cables, Cables bench, MagicMotorSport – Flex
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42C
Accessories adapters cables, Cables bench, MagicMotorSport – FlexAdapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42C
Out of stock
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42C
Connectors size C, which are included in the basic FLEX device.
The FLK42C adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
SKU: FLK42C - Accessories adapters cables, Cables bench, MagicMotorSport – Flex
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42D
Accessories adapters cables, Cables bench, MagicMotorSport – FlexAdapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42D
Out of stock
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42D
Connectors size D, which are included in the basic FLEX device.
The FLK42D adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
SKU: FLK42D - Accessories adapters cables, Cables bench, MagicMotorSport – Flex
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42E
Accessories adapters cables, Cables bench, MagicMotorSport – FlexAdapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42E
Out of stock
Adapters Bench FLEX (for connecting ECU/TCU with FLK35) FLK42E
Connectors size E, which are included in the basic FLEX device.
The FLK42E adapters allow the FLK35 coloured kit cables to be connected to the ECU and TCU modules.
SKU: FLK42E
