, ,

Software Abrites AVDI VN002

Availability:

Available on backorder


With this special function you will be able to adapt the module. This is one of the most representative things about Abrites and definitely one of the most frequently used functions by our customers. We are always at the forefront when it comes to adapting both used and new modules installed in Volkswagen, Audi, Seat, Skoda, Bentley, Lamborghini and even some Prosche models. From sound amplifiers and MMI units to ECUs and TCUs and everything in between.

10,203.31 +VAT

Previous lowest price was 12,544.29.

Available on backorder

Abrites AVDI VN002

Here is what you can use the VN002 function for:
– Diagnostic extraction and display of immobiliser related data. Possibility to align immobiliser related data – counter/ecu. Display of immobiliser related data from flash memory dump and micronas eeprom in IPC.
– Reading/programming of immobiliser memory in the counter.
– Reading/updating immobiliser-related data
– Reading/updating immobiliser data in VDO dashboards with NEC microcontroller (2009+) via OBDII
– Extraction and reading of PIN code, control of control module configuration memory content, component security data from EDC16, MED9.x, Simos PPD 1.1/1.5, Magnetic Marelli 4HV,7GV engine control units. Emergency start-up of EDC16 engine control units. The entire EEPROM for EDC15/ME7/EDC16 can be read out. For MED9 and Simos, only PIN / CS / MAC is displayed.
– Advanced diagnostic functionality – Fault data and electronic control unit configuration memory can be managed. Reading / Updating of Siemens airbag control data (CAN bus – ISO15765). Audi A6/Q7/Allroad, VW Golf 5…, Skoda Octavia II…, Seat Altea… With this special function we can Read/update the memory data of the airbag module. Clears the failure data of the airbag module.
– Units supported Read/Update data:
1. all Siemens CAN airbag 2003-2008 such as 4F0959655B (Audi A6/Q7/Allroad 2003-2008), 1K0909605AB, 1K0909605C, 1K0909605AD, etc….
2. K-Line airbag (Siemens and Bosch) – 1C0 909 605 C, 8L0 959 655 A, 1J0 909 609, 6Q0 909 605 C,6Q0 909 605 A, 6Q0 909 605 B, 3B0 959 655 B, 1C0 909 605 F, 1C0 909 605 H, 1J0 909
607, 1J0 909 603, 4B0 959 655 C, 4B0 959 655 J, 4D0 959 655 C, 8L0 959 655 F,8A0 959 655
C, 8A0 959 655 K, 8A0 959 655 K, 4D0 959 655 H, 8D0 959 655 C, 8D0 959 655 L.
– Preparation of a ready-made diagnostic adaptation key for vehicles with BCM2 – Audi A4, S4, RS4, A5, S5, RS5, A6, A7, A8, Q5 / VW Touareg
+ ILM module (front passenger) (ILM Beifahrer) – Audi A8 2003-2010
Component protection generation 2
EZS-Kessy Audi A6/Q7 2004-2009 by OBDII
Comfort module Audi A6/Q7 2004-2009 by OBDII
Climantronic Audi A6/Q7 2004-2009 by OBDII
airbag Audi A6/Q7 2004-2009 by OBDII
Airbag Audi A4/A5/Q5 2008+ Bosch by OBDII
Audi A6/Q7 2004-2009 clocks by OBDII
Audi A4/A5/Q5 clocks 2008+ by OBDII
Infotainment module Audi A4/A5/Q5 2008+ by OBDII
– All other modules (e.g. DSP) with second-generation component protection
for A6/Q7 2004-2009 and A4/A5/A5 only possible if you have the memory from which the module was built + Adaptation of engine control units to the vehicle – EDC16,EDC17, MED17, MED9, Simos PPD, ME7.5.20, ME7.5.30
Kessy Audi A8/VW Touareg/Phaeton
VW Passat B6/CC comfort module
Audi A6/Q7/Allroad/A8 gearbox
EZS-Kessy Audi A6/Q7/Allroad
BCM2 immobilzier – Audi A4, S4, RS4, A5,S5, RS5, A6, A7, A8, Q5 / VW Touareg
+Reading of PIN and CS from EDC17/MED17 of the engine control unit. With this function it is also possible to read engine control units from 2012+ units that have been updated and cannot be read via OBDII. With this special function, the EDC17/MED17 is not read via OBDII – you should have a direct connection to the engine control unit.

It is also possible to do this at the table, just connect 12V, ignition, CAN-H and CAN-L. It is possible to read the ECU also in the car, but you need to find somewhere the CAN-H (orange-black) and CAN-L (orange-brown) wires. So connect them to the AVDI and you will be able to read the engine control units.
The ECU can also be read in the car, but in this case we need to find the CAN-H (orange-black) and CAN-L (orange-brown) wires, then connect them to the AVDI which will enable us to read the engine control unit. + adapt the transmission control unit (TCU) to the immobiliser (BCM2). To do this, the TCU must first be read. The TCU cannot be read via OBDII,
but it can be read by connecting the TCU on the table or by connecting the AVDI to the CAN-Bus socket of the car.
DSG and CVT gearbox controllers are additionally supported for adaptation (DQ200 and DQ250).
To read from the CAN-Bus socket, we need to find the orange/black and orange/brown wires and then connect them to the AVDI. – orange/black <-> CAN-H (PIN6 of the OBDII)
– orange/brown <-> CAN-L (PIN14 of the OBDII)
– ground <-> GND (PIN4 of the OBDII)
– 12V <-> 12V (PIN16 of the OBDII)
+ Reading PIN/CS/MAC from the Simos PCR 2.1 engine control unit.
Information: Function requires internet connection
This function includes all the functions listed below:
– AN043, AN045 AN046, AN047, AN048, AN049, AN052, AN053, AN055, AN056,
AN057, AN058.

Full details on how to use this special feature of ABRITES can be found in the manual HERE.

Please note that an interface with an active AMS subscription is required to use this function. Tokens are not required.